|当前位置 -> 环亚ag88－ 热风炉知识－ 工业热风炉使用效率不足的原因 发布时间：(2018/12/9)关键词：环亚ag88|
环亚ag88 www.cgfly.cn 眼下，我国各地都出台了对高耗能燃煤热风炉进行拆除、关?；蚋脑斓囊?。此前，环保部发布的《关于执行大气污染物特别排放限值的公告》也显示出我国的环境改善将从末端治理走向源头控制。有关人士表示：我国工业热风炉在节能、减排两个方面都有很大的改善空间。工业热风炉使用效率不足的原因：效率不足节能潜力起大.我国工业热风炉量大面广，平均容量小，且以燃煤为主。虽然我国燃煤工业热风炉的设计效率与国外相比差距不大，但实际运行效率只有65%左右，比国外先进水平低10%-15%，一台燃煤热风炉通过冷凝水回收、提高炉内空气温度及安装煤斗分层燃烧等技术改造，达到了最大程度的节能减排效果，一年下来节约成本约200多万元。
At present, all parts of our country have issued the requirements for the demolition, shutdown or transformation of high-energy coal-fired hot blast stoves. Previously, the announcement on the implementation of the special emission limits of atmospheric pollutants issued by the Ministry of Environmental Protection also showed that China's environmental improvement will move from end-to-end treatment to source control. Relevant people said: China's industrial hot stoves in energy saving, emission reduction in two areas have great room for improvement. The reasons for the inefficiency of industrial hot-blast stoves are as follows: insufficient efficiency and high energy-saving potential. China's industrial hot-blast stoves are large in volume, small in average capacity and mainly coal-fired. Although the design efficiency of China's coal-fired industrial hot-blast stove is not much different from that of foreign countries, the actual operation efficiency is only about 65%, which is 10%-15% lower than the advanced level of foreign countries. A coal-fired hot-blast stove has achieved the greatest degree of energy saving and reduction through the technical transformation of condensate recovery, increasing the air temperature in the furnace and installing the stratified combustion of coal hoppers. The drainage effect saves about 2 million yuan a year. 我国燃煤工业热风炉运行效率不足的原因比较多。总结后，主要有几个方面：
There are many reasons for insufficient operation efficiency of hot blast stoves in coal-fired industry in China. After summarizing, there are mainly several aspects:
First, the design and manufacture of industrial hot blast stoves pay more attention to the compressed parts in the design, but not to the combustion devices.
2. Reasons for the use of industrial hot-blast stoves. The capacity chosen by users of hot-blast stoves does not match the actual capacity.
3. The types of coal used in industrial hot-blast stoves do not conform to the design types of coal used in hot-blast stoves. The calorific value, volatile matter or particle size of coal used do not conform to the design requirements of hot-blast stoves.
4. The relevant regulations and regulations on energy-saving supervision of industrial hot stoves are not perfect, and the technical standards are relatively lagging behind.
Revamping Technology of Hot-blast Furnace and Furnace into Mainstream
In the future, some old coal-fired hot stoves with low efficiency and serious environmental pollution will be eliminated, and the existing coal-fired hot stoves will be technically reformed according to local conditions. In areas rich in natural gas and other resources, coal is replaced by gas. In areas poor in gas resources, solar collectors are used to replace small coal-fired hot stoves and other measures.
At present, many manufacturers have chosen to reform the hot-blast stove. In the design and manufacture of industrial oil, gas and coal-fired hot-blast stove, in order to prevent the corrosion and ash plugging of the heating surface at the tail of the hot-blast stove, the standard smoke exhaust temperature is not less than 180 (?) C, up to 250 (?) C. High-temperature smoke emission not only causes a lot of heat energy waste, but also causes a lot of heat energy waste. Environment pollution.
|相关阅读：生物质热风炉的优势越来越明显 | 全面论述生物质热风炉启动注意事项 | 环亚ag88|
版权所有：无锡市联赢干燥设备有限公司主营：环亚ag88 电话：0510-83955910 传真：0510-83051522 技术支持：易商科技